Features
- Horizontal injection system, vertical clamping system.
- Nozzle connected to gear pump directly, without heating pipe, avoid material crystallization.
- Nozzle connected to melting tank, injection unit back and forward by air.
-
Melt tank made from aluminum alloy, precision machining then coated with Teflon, heating evenly and rapidly and clean easily.
-
Equipped with Ejection system driven by Pneumatic cylinder.
-
Two tie bar design for molding small parts, operation easily.
-
Equipped with Light Curtain、 Dual Palm buttons and safety cover for operator safety.
-
Machine driven by air pressure and single phase electric power source. Energy saving, low pollution and no oil leakage risk made from hydraulic system suitable for clean room and laboratory.
- Low pressure molding is an innovative process between injection molding and potting. It’s molding at very low pressure with hot melt adhesives for low injection pressures. A cost effective alternative to epoxy potting. It offers superior strain relief compared to conventional plastic injection molding for cable、wires and connector.
- Complete sealing of the components providing water-tight encapsulation.
-
Short cycle time (14-45 seconds) to complete part.
-
The Pressure adjusting valve control the pressure of injection.
-
Three PID thermal temperature control zones (Melting tank and nozzle)
-
Multiple language HMI and user friendly PC Base
-
Complete operation history of setting & alarm
-
1000 sets of mold documents can be export as backup.
-
Offer one axis control for servo motor.
-
Built in USB /Ethernet/Print port/CF Card.
Main specifications
Low Pressure Injection Molding Turn-Key Solution Clamping force 1ton
| Injection Unit | ||||
|---|---|---|---|---|
| Injection Type | Horizontal Injection | |||
| Capacity | l | 3.5 | ||
| Injection Capacity | cm3 / r | 8.98 | ||
| Pump Speed | r.p.m | 0~51 | ||
| Nozzle Stroke | mm | 30 | ||
| Nozzle Contact Force | ton | 0.12 | ||
| Clamping Unit | ||||
| Clamping System | Air Hydro Booster | |||
| Clamping Force | ton | 1 | ||
| Opening Stroke | mm | 160 | ||
| Mould Space | mm | 285 | ||
| Min Mould Space | mm | 125 | ||
| Overall Size of Platens | mm | 480*140 | ||
| Space Between Columns | mm | 360 | ||
| Ejector Force | ton | 0.12(Pneumatic) | ||
| Ejector Stroke | mm | UP 10 | ||
| Electrical Equipment & General | ||||
| Power Source / Voltage | V / HZ | 1 ø 220/(50/60) | ||
| Drive Motor | kw | 0.12 | ||
| Heater | kw | 3.92 | ||
| Temperature Control Zone | zone | 3 | ||
| Pressure Pneumatic | kg / cm2 | 6 | ||
| Dimension of Machine (L*W*H) | m | 1.2*1.0*1.8 | ||
| Weight of Machine | ton | 0.3 | ||
| Option | ||||
| Size Of Slide Table | mm | 340*140 | ||
| Slide Table Stroke | mm | 200 | ||
Low Pressure Injection Molding Turn-Key Solution Clamping force 4tons
| Injection Unit | ||||
|---|---|---|---|---|
| Injection Type | Horizontal Injection | |||
| Capacity | L | 3.5 | ||
| Injection Capacity | mL / r | 8.98 | ||
| Pump Speed | r.p.m | 0~51 | ||
| Nozzle Stroke | Mm | 30 | ||
| Nozzle Contact Force | Tf | 0.12 | ||
| Clamping Unit | ||||
| Clamping System | Air Hydro Booster | |||
| Clamping Force | Tf | 4 | ||
| Opening Stroke | Mm | 160 | ||
| Mould Space | Mm | 285 | ||
| Min Mould Space | Mm | 125 | ||
| Overall Size of Platens | Mm | 480*140 | ||
| Space Between Columns | Mm | 360 | ||
| Size Of Shuttler Platen | Mm | 340*140 | ||
| Shuttle Plate Stroke | Mm | 200 | ||
| Ejector | Air | |||
| Ejector Force | ton | 0.12(Pneumatic) | ||
| Ejector Stroke | Mm | UP 10 | ||
| Electrical Equipment & General | ||||
| Power Source / Voltage | V / HZ | 1 ø 220/60 | ||
| Drive Motor | kw | 0.12 | ||
| Heater | kw | 3.92 | ||
| Temperature Control Zone | zone | 3 | ||
| Pressure Pneumatic | kg / cm2 | 6 | ||
| Dimension of Machine (L*W*H) | m | 1.2*1.0*1.8 | ||
| Weight of Machine | ton | 0.3 | ||
| Option | ||||
| Size Of Slide Table | mm | 340*140 | ||
| Slide Table Stroke | mm | 200 | ||
